Why does the Kandy washing machine not wring out? 6 main causes of the problem

The next wash ended in trouble – the Candy washing machine does not wring out the laundry. How to be? Disable and unscrew manually? Or start the program over again? Get to the bottom of the problem first, then start looking for solutions.

Why is spinning not working?

The causes of the problem do not always lie in breakdowns. Sometimes the manufacturer is not to blame, but the point is user negligence, and it doesn’t matter which SMA is regular or vertical. Remember if you changed the settings during the last wash? Here’s what to check:

  • Spin speed. Perhaps the function is completely disabled after washing delicate laundry? If so, then just turn on the program. Increase the number of revolutions so that the clothes come out almost dry.
  • The presence of an imbalance. The electronically controlled machine automatically distributes the laundry in the drum. When the system detects an imbalance, further work stops until the balance is restored. It is worth stopping the program and distributing clothes manually.
  • Drain filter. During operation, debris, hair, villi accumulate in the filter. It is enough to unscrew the part in the lower part of the case, substitute the container and clean the inlet and the filter itself.

Everything is checked and cleaned, but does a bad spin make itself felt? Then you have to take radical action. Namely, to disassembling and diagnosing parts of the Kandy washing machine.

SMA Candy does not wring out: what to do?

There are at least five reasons why the washer refuses to spin. We list only the characteristic problems for the Kandy lineup. Most often breaks in washing machines:

  • drain pump;
  • main module controller;
  • tachogenerator.

Each problem is accompanied by characteristic symptoms, which makes it easier to find the problem. Looking to figure it out on your own? Then disconnect the equipment from the mains and drain the water from the filter.

Drain pump malfunction

The pump draws water from the tank. The device pumps the liquid into the sewer, after which the washing machine starts spinning. The problem may be in the electrical or mechanical part of the pump. To determine the cause, disconnect the hoses from the body and turn the machine on its side. The pump is under the bottom.

Progress:

  1. Release the pump from pipes and hoses. To do this, unscrew the fastening screws and wring out the clamps.
  1. Inspect the pump mechanism for blockages. Threads and hair are often wound onto the impeller, which blocks its operation. Remove all debris.
  2. Check the electrical component. To do this, a multimeter is connected to the contacts and the resistance is measured. Readings of 0 and 1 on the screen indicate a motor failure, and a three-digit number indicates a breakdown of the electronic module.

To replace the part, turn the pump to the right and install a working pump. At the same time, clean the nozzles and hoses from debris, this also affects the quality of the wash. If everything is in order with the pump, do not rush to collect the car.

The video will help you replace the drain pump yourself:

Breakdown of the speed control sensor

Not far from the pump is the engine, and on it is a tachometer. This device controls the number of revolutions of the motor, after which it transmits information to the control module. So the technique “understands” what speed needs to be set.

What if the sensor is broken? Then the machineKandy» does not gain momentum and does not spin. As a result, you get wet clothes that have to be wrung out and dried for a long time. The tachometer is located on the motor shaft, so dismantling is indispensable. How to help:

  1. Unscrew the fasteners and remove the rear cover of the CMA.
  2. Remove the belt from the tank pulley.
  3. Unscrew the bolts holding the motor, disconnect the terminals.
  4. Examine the sensor.

Sometimes, due to strong vibrations, the tachogenerator is displaced, the contacts move away. Reconnect all connections. Check the electrical part. Attach the multimeter probes to the sensor contacts. If the indicators are 60-70 ohms, then the device is working. If not, required replacement.

Electronic controller problems

The most difficult problem for the average user. If you are not a master of electronics, then it makes no sense to understand. If desired, you can visually inspect the part. Suddenly there are burnt tracks and swollen capacitors. Then you can definitely say what is the cause of the breakdown.

The control module is responsible for all processes in the washing machine. When the washing machine does not wring out well, it does not start the set mode at all, it does not pull out at speed – the module is to blame. True, only a test can prove this.

Here is what you need to do:

  • Remove the CMA top cover by unscrewing the bolts at the back.
  • Take out the powder tray.
  • Loosen the control panel screws and remove it from the case.
  • The board is attached on the back.
  • Inspect the surface for damage.

If nothing could be found, then you will have to contact the master. The specialist will ring the details with a tester. Perhaps it will cost a small repair, rather than a complete replacement.

Candy Smart cars and other electronically controlled models must be protected from power surges. Then it will be possible to avoid damage to the electronic board and other elements. We recommend periodically cleaning the filters and not overloading the equipment – manufacturers do not write instructions in vain. Compliance with the rules will affect the life of the machine. And do not forget that you can save many appliances with the help of stabilizer.

Leave a Reply