What do Hoover washing machine error codes mean?

Error Codes (shows on display) A series of indicator flashes (the number of flashes through a pause is determined) Error value Reasons for the appearance of the code How to troubleshoot E 01 1 CM door not closed properly. Blocking issues. The door lock or locking device (UBL) is out of order. Control module failure.

1. With error E 01, the door handle is checked, the locking tongue is put in place, or the handle is replaced.
2. The electronic interlock (UBL) is being examined. UBL is being replaced.
3. Checking the contacts of the control unit. Wiring replacement.

E 02 2 Problems with water intake.

If the code E 02 is on the display, there is probably a blockage in the filling system.

Perhaps the control unit has failed.

To reset an error:

1. Open the water supply tap.
2. Clean the strainer in the filling valve. Check valve, replace if damaged.
3. Clean the pressure switch tube. Check the pressure switch. If defective, install a new part.
4. Repair of the electronic module.

E 03 3 When E 03 is lit, the CMA does not drain water.

• There is a blockage in the drain system.
• Breakage of the pump (drain pump).
• Pressure switch problems.
• The wiring from the module to the pump or pressure switch is broken.

1. Checking and replacing the drain pump.
2. Cleaning the drain pipe from the tank to the pump.
3. Installing a new pressure switch.
4. Inspection of the wiring loop, isolation of damaged areas, replacement of wires.

E 04 4 There is a problem with the water inlet valve in the Hoover washing machine. Fill valve failure. To remove error E 04, you need to check the filler valve. In case of malfunction, a new valve is installed. E 05 5 E 05 indicates that there is no water heating.

• The heating element or temperature sensor is out of order.
• Problems with the control board.

1. Ringing the heating element with a multimeter. Heating element replacement.
2. Installation of a working temperature sensor.
3. Diagnosis and replacement of the control board.

E 06 6 E 06 – error of the electronic unit (EEPROM). Or the balance during washing is disturbed (imbalance).

• Due to a short circuit or exposure to moisture, the electronic module is faulty.
• The laundry is unevenly distributed in the drum.

1. Replacing the control module.
2. You need to open the door and manually distribute the laundry in the drum.

E 07

E 08

7-8 Codes E 07 and E 08, depending on the model, say: the hatch door lock is jammed, or the CMA engine is faulty.

• The drum abruptly changes speed and frequency of rotation.
• Engine tachometer malfunction.

1. Checking and repairing the door lock.
2. Inspection and replacement of the tachometer, which is responsible for the speed of rotation of the motor.

E 09 9 Washer motor error. The motor is not running, the impeller is not rotating. The display shows error code E 09, testing does not stop. Failure of the triac or control board requires their replacement.

E 11

E 12

11-12 Open circuit. The wiring circuit between the electronic board and the drying heater is broken. At signals E 11 and E 12, the connecting circuit is inspected, defective elements are changed.

E 13

E 14

13-14 E 13 and E 14 – electronic module error. The machine washes in cold water, no heating. Malfunction of the heating element (thermal sensor) or control unit. The heating element and temperature sensor are checked. When parts break, new ones are installed. E 15 15 If the display shows E 15, the electronic module has failed. Damaged control board memory. Replacing the electronic board. E 17 17 Tachometer broken. The board does not receive a signal from the tachogenerator and issues code E 17. Inspection of the tachometer. Installing a new device. E 18 18 The electronic unit has failed. Module failure. When E 18 appears, it is necessary to replace the electronic control unit.