Samsung dishwasher errors: how to fix

Malfunction code What error means Causes of appearance What do we have to do E1 Long set of water.

1. Lack of water supply in the system.

2. The water supply tap is closed.

3. Clogged or pinched inlet hose.

4. The door is not closed properly.

5. The mesh filter is clogged.

1. Turn off the faucet and check for water in the water supply.

2. Turn the stopcock, it may have been blocked.

3. Inspect the water intake hose. It must be level. Maybe he was bent over or pinched by some object.

4. Close the door more tightly. It is equipped with a lock. Until the lock locks the door, the wash will not start.

5. Clean the mesh filter. It is located at the junction of the inlet hose with the PMM body. Turn off the water, unscrew the hose and rinse the mesh.

E2 What does the error code mean: the machine does not drain the water after washing the dishes.

1. Problems with the drain hose.

2. The filter is clogged.

3. Clogged drain system.

4. The drain pump in the car is clogged.

How to fix a crash:

1. Inspect the drain hose that connects the dishwasher to the drain. If it is pinched or twisted, the water will not drain.

2. The filter located at the bottom is clogged with food debris. For normal draining, clean the filter. But first, press the “Drain” button.

3. To check the drain hose for blockage, disconnect the end of it from the sewer and lower it into a bowl. If the drain does not occur, then you need to remove the hose and clean it from food debris and dirt.

4. In case of blockage, the drain pump can be cleaned with your own hands if you are familiar with the design of the dishwasher. But it is better to call the master.

E3 No water heating.

1. Faulty heating element of the machine.

2. The thermostat is broken.

3. The control module has failed.

Self-repair when an error is detected:

1. Check the correct connection of communications. If the machine is new, you may have mixed up the hoses.

2. Check the set mode. If a delicate wash is set, the heating temperature will not exceed 40 degrees.

3. Inspect the Samsung dishwasher filter for blockage. With reduced water circulation, the heating element does not turn on.

4. Inspect the heating element. If it is overgrown with scale, then the element needs cleaning. If the heater burned out, a complete replacement will be required.

5. Install a new thermostat if there is a problem.

6. Only the master can find out the cause of the module failure, as well as replace it.

E4 The meaning of the code on the Samsung dishwasher: too much water in the tank.

1. The sensor that controls the water level in the tank is faulty.

2. Problems with the water intake valve.

How to help:

1. Check the level sensor, replace if defective.

2. Inspect intake valve. Replace if necessary.

E5 Water pressure too low.

1. Problems with the level sensor.

2. The dishwasher filter is clogged.

3. Clogged or kinked inlet hose.

1. Inspect the level sensor. In the event of a breakdown, the sensor needs to be replaced.

2. Clean the filter from blockage.

3. Check the inlet hose. Fix its location.

E6-E7 Problems with the temperature sensor. The thermostat does not work, water heating does not start. A new temperature sensor needs to be installed. E8 Alternate valve failed. If, after checking, a breakdown is detected, the valve is replaced. E9 The program start button does not work.

1. Detergents got into the connectors of the button, and it stuck.

2. During the operation, the button was pressed through.

3. There was a short circuit in the contacts leading to the button.

The panel with the button needs to be disassembled and cleaned. Check the contacts of the button, if they are burned out, a replacement is needed. UC Incorrect mains voltage. If the mains voltage is too low or too high, the dishwasher will not work, displaying an error. You can wait until the voltage resumes, or call an electrician. EA Dishwasher water level too high.

1. Problems with the drain hose.

2. Incorrect level sensor data.

1. Inspect the drain hose. If it is pinched or clogged, the water will not drain well from the machine. The hose needs to be cleared.

2. Check the water sensor is working. Replace if necessary.

3E2 No signal from the tachometer. It is necessary to check the wiring connections between the motor and the tachometer. Die The door is not closed properly. Press the machine door harder, otherwise the wash will not start. Le A water leak has occurred. It is necessary to inspect the body of the dishwasher, determine and eliminate the cause of the leak.