Contents
In the Atlant washing machine, the None error was displayed on the display. What does this mean? Your Atlant washing machine produced too much foam during washing.
On non-shielded electromechanical models, all 4 LEDs are lit with a None fault code.
Read on for what to do and how to fix the problem.
Note! If you see that the Atlant washing machine shows the None error on the display, and the floor is flooded with foam, immediately disconnect the SMA from the network.
Causes of a malfunction
The fact is that an excess of foam can get to the electronic components or the engine. This increases the chance of a short circuit.
Do the following:
- Manually drain the water using the drain filter. In most Atlant washing machines, the filter is located on the front panel below, behind the hatch. Open the hatch, substitute the container and remove the filter.
- Remove all laundry from the machine.
- Clean the foam from the tank.
- Turn on rinse mode. Repeat it until all the foam is gone.
- Dry the filter.
- Wipe down the control panel thoroughly.
To understand how to fix the situation and remove the None error, you need to understand the causes of the malfunction. This often happens:
- As a result of the use of low-quality or non-machine-washable powder.
- Due to excessive use of detergents.
- Due to the softness of water: the softer the water, the better the powder dissolves and foams.
- When washing voluminous and porous linen (curtains, tablecloths, tulle). Just because the drum is full of light stuff doesn’t mean you have to pour in a lot of powder. Washing this linen is accompanied by a large formation of foam.
How to fix the situation
How to reset the None error and solve the problem if you poured powder according to the instructions, did not install a cleaning filter and did not wash porous items? Why then does the Atlant washing machine give an error code?
Let’s analyze the main causes of the problem.
The rubber cuff has lost its tightness
The cuff could leak over time, as a result of which it lost its tightness and began to let water through. Small sharp objects during washing may damage the cuff.
How to check and replace:
- Disconnect the Atlant washing machine from the mains.
- Bending the cuff, you will see a metal collar.
- Using a screwdriver, pry it around and remove the clamp.
- Detach the door seal from the top panel and tuck it inside the machine.
- Unscrew the two screws and remove the top panel of the Atlant washer.
- To remove the inner clamp, unscrew the fastening screw.
- Now remove the cuff from the front.
- Inspect it for damage, install patches or replace the cuff.
The video will help you with the work:
Disturbance in the drain system
If, after checking the cuff, the None error still lights up on SM Atlant, you need to check the entire drain system. Signs of its violation are the formation of water and foam under the machine.
For check:
- Inspect the drain hose and its connection to the Atlant machine and the sewer. Tighten all connections, check the hose for damage and cracks, replace if necessary.
- The drain filter is also inspected for leaks.
- The pump is checked. Once you have reached the pump, look for water under it. Then carefully inspect the pump.
- The drain pipe must be replaced if damaged. But first, let’s figure out how to get to it.
How to replace the pipe from the tank to the pump and remove the None error in the Atlant washer:
- Drain all water from the machine and unplug it from the mains.
- Remove the dispenser tray and check the drain filter for water residue.
- Turn off communications.
- Put the Atlant washing machine on its side, opening access to the bottom.
- Loosen the clamps that secure the pipe.
- Disconnect the hose from the tank.
- Unscrew the pressure chamber from the connection to the tank.
- After disconnecting the clamp, remove the pipe.
- Install the new element in reverse order.
Be attentive to the choice of powder for the Atlant washing machine. If the error is no longer displayed on the scoreboard, then everything is done correctly.