Miele washing machine error codes (Mile) – what to do

Error code What it means Causes How to fix the situation F01 Drying temperature sensor defective. Due to a short circuit, the thermistor that controls the drying temperature has failed.

1. Inspection and replacement of the temperature sensor in case of malfunction.
2. Check contacts and wiring. Repair of damaged areas.

F02

F03

F04

The error means that there is a problem with the drying temperature sensor. Why is the code on the CMA scoreboard:

• Rupture of sensor connections.
• Thermal sensor failure.

To reset an error:

1. All contacts between the temperature sensor and the module are tested.
2. The thermistor is replaced with a good part.

F10 There was a problem with water filling. Causes:

• There is no water in the system, or the inlet valve is closed.
• Clogged water intake hose, inlet filter.
• Problems with the main module.

To solve the problem, do this:

1. Open the stop valve.
2. Remove and clean the intake hose and the filter mesh between it and the valve.
3. Diagnostics of the electronic board.

F11 No water drain. For what reasons the code was displayed on the screen:

• Low pressure in the water supply.
• Clogged pump filter, drain pipe or pump.

How can I remove the error:

1. The pressure in the water supply is checked.
2. The filter, pipe and drain pump are cleaned.

F15 Hot water intake. Check if the connection is correct. Shut off the hot water supply. F16 Too much foam.

• The dose of detergent has been exceeded.
• Water drains badly.

What to do:

1. Further reduce the dose of powder.
2. Check the drain pump and pipe for blockage. To eliminate foam, turn on the rinse mode.

F19 Water sensor malfunction. Checking the sensor. It is possible to hit a small object. F20 Malfunction in the heating system. Why did the error code appear in the Miele washing machine:

• Breakage of the heating element (heater).
• Thermal sensor malfunction.

How to fix the situation:

1. Replace heater.
2. Install a new temperature sensor.

F29 Drying heater failure. The drying heater does not work. Heating element replacement. F34 The hatch does not close tightly. Why is the washer giving an error:

• The mechanical parts of the door are worn out: lock, tongue, handle.
• Breakdown of the electronic lock of the hatch (UBL).

How to repair a Miele washing machine:

1. Replacement of broken door elements.
2. Installing a new blocking device.

F35 Sunroof door cannot be opened. What happened:

• There was a blockage in the lock hole.
• Faulty elements of the control board.

1. Work is underway to open the door.
2. Then the keyhole is inspected and cleaned.
3. The electronic board is being repaired.

F39

F41

F43

F45

F50

Failure of the electronics. Problems with the control module. Change or repair of the main unit. F46 Incorrect display connection. Rupture of contacts, or breakdown of the control board. Repair and replacement of elements. F47 There is a problem with the BAE/SLT interface. F48 There is a problem with the SLT interface. F51 Pressure switch faulty. Pressure switch problem. Installation of a working element. F53 The speed sensor has failed. Sensor failure. Replacing an element. F55 Incorrect operation of the SMA time control element. Part change. F56 Reduced speed (does not reach 400 rpm). Probably the engine tachometer is broken. Checking the winding and the tachometer itself. F62 Mode selector does not work. Installing a new selector. F63 Problems with the operation of the system that controls the trajectory of water. Checking and repairing the system. F64 Trajectory sensor failed. Sensor change. F65 The backlight in the drum is faulty. F81 Drying unit does not work. Replace dryer unit with CMA Mile. F83 Drying temperature is too high. The thermistor may have broken. Checking the thermistor and heater. F92 The washing machine is likely to be damaged by a fungus. F93 Breakdown of the relay of the additional unit. Repair, relay change. F96 Alternative water supply does not turn on. Checking elements. F100 Lost communication with IK6.