Kerting Dishwasher Errors – Decoding Codes

Is there an error on the display of the Korting dishwasher? Has the equipment stopped working, beeping and flashing? So she tries to inform you about a problem in the system.

The electronic module controls all parts and assemblies in the machine. As soon as a breakdown occurs, it displays an error code on the scoreboard so that you can find and fix the problem as quickly as possible. Explanation of all icons below.

Error codes PMM Korting (Kerting)

If you notice them on the screen, the first thing to do is rule out a system failure. To do this, try resetting the error:

  • unplug the PMM plug from the socket;
  • wait 10-15 minutes;
  • restart.

If the code no longer appears on the display, you have successfully eliminated the cause of its occurrence. But if it lights up again, decipher its meaning from the table and try to fix the problem.

Error codeValueCauses of appearanceHow to fix the situation
E1There were problems with water intake. The timeout has expired.
  • There is no water in the system.
  • Shut-off valve closed.
  • The device is connected incorrectly.
  • Solenoid valve defective.
  • Inlet filter clogged.
  • The level sensor is broken or gives incorrect readings.
  • Burnt out wiring.
  • The electronic board has failed.
What to do:
  1. Check for water in the system. Wait for her to show up.
  2. Turn the shut-off valve, it may have been blocked.
  3. Check the dishwasher wiring diagram in the instructions. Make sure the hoses are connected correctly.
  4. Diagnose the intake valve: apply voltage to it. Check the electronics with a multimeter. Replace valve if damaged.
  5. Clean the intake filter from dirt. To do this, disconnect the hose from the body, remove the filter and rinse under a tap.
  6. Inspect the level sensor, measure the contact resistance with a multimeter. The pressure switch cannot be repaired, only replaced.
  7. Consistently inspect the internal wiring. Replace burnt elements or cables.

It is better to entrust the repair of the control board and accurate diagnostics to a specialist.

E2The water doesn’t go down the drain.Why PMM “Kerting” may show an error:
  • the drain hose is kinked, kinked, or clogged with debris;
  • the drainage filter is clogged with food debris, small debris, napkins;
  • pump impeller blocked;
  • the drain pump is faulty;
  • the pressure switch is unusable;
  • the control module does not work correctly: the triac burned out or it completely failed.
How to fix the problem:
  1. Unscrew the drain hose. Rinse it under running water. Make sure that it is even, without kinks.
  2. Open the hopper door. Unscrew the drain filter in the pan. Clean the part with a brush and detergent, rinse under a tap.
  3. Remove the pump cover, inspect the impeller, remove foreign objects. To get to the pump, disassemble the dishwasher. Check the part for blockage, check the electronics with a multimeter.
  4. Diagnose and replace the pressure switch.
  5. Look at the board. If burnt parts are visible on it, contact the master. He will restore her work.
E4Overflow Water in the PMM tray.What happened:
  • there was a leak in the car: water got into the pan, where the float sensor worked;
  • protection “Aquastop” is out of order.

What to do:

1. Inspect the dishwasher hopper, look for a leak. Check hose and pipe connections. Make sure they are not kinked or leaking. Also inspect the rubber seal on the door. Replace defective elements.

2. Diagnose the Aquastop sensor. It can be located at the bottom of the car. Mechanical protection is part of the inlet hose. Therefore, if it leaks, replace the hose completely.

E8Flow sensor failure.What is the cause of the malfunction:
  • the sensor is out of order;
  • the wiring from the module to the sensor burned out, the connections were broken;
  • burned out control module.
Do-it-yourself repair:
  1. Checking and replacing the flow sensor.
  2. Diagnostics of wiring, connections. In case of violation of the insulation, the presence of burnt parts, a new cable is installed.
  3. The module is checked and replaced if it fails.

Now you know what to do when an error occurs in the Kerting dishwasher. Follow the rules of operation to avoid premature breakdowns.

Leave a Reply