Contents
How to turn on the boiler after installation? If you mounted it yourself, there may be problems. In this article, we will tell you how to properly start the device, even if you only need it during a seasonal water outage.
Connecting the water heater to the network
Where to begin:
- If you have a water supply, and the boiler is already connected to the pipes, turn off the hot water valve. Even when installing a check valve, this safety measure must be observed. Otherwise, the hot stream will go to the neighbors.
After overlapping, make sure it is reliable. Open the faucets to be sure: if there is no water, close them back.
- To correctly identify the location of the hot and cold pipes, turn to face the boiler. Cold is on the right, hot is on the left. Usually they are indicated by blue and red nozzles.
- Now turn on the blue faucet (cold) and only then the red one (hot). Open the faucet on the mixer, wait for the air to escape and the liquid to fill the device. You will determine the moment of filling by the fact that a strong pressure of water will come out of the tap.
It remains to plug the plug into the outlet – the work is over.
Some users believe that in order to save electricity, it is beneficial to disconnect the boiler from the network after heating. However, the storage tank has a design that constantly maintains heat. It is more profitable to keep the set temperature than to start heating from scratch.
This applies not only to the cost of electricity, but also to the duration of work:
- The tank in which the water is located is less corroded. The liquid inside does not stagnate when heated, microorganisms do not multiply in it.
- If the heater is disconnected from the mains in a cold room, the system may fail. First of all, the temperature sensors break.
- Each time, disconnecting the device from the network, you can perform an incorrect start – without water, which will lead to equipment breakdown.
First launch of a boiler from different manufacturers
Depending on the brand, connection features may vary.
Ariston (Ariston)
As soon as water has been collected and you have completed the connection to the network, proceed as follows:
- Make sure that the indicators on the panel light up.
- After that, the temperature lights should blink. This means that the boiler is not working.
- On the panel, press the power key.
- Based on the indications on the display (in the current state), set the desired heating temperature using the thermostat or keys.
- Press the power button to select the mode from 1500W to 2500W.
If “memory” is not installed in your model, after turning off, you will have to re-set the settings.
Thermex (Termex)
The device of this manufacturer has a simple control. After connecting to the network, it is enough to turn the thermostat to the desired position – heating will begin. After 30 minutes, you can check how the temperature is gaining on the sensor. Open the faucet – is there a hot stream? So you did everything right.
Electrolux (Electrolux)
To turn on water heating, press the Power button. Set the required indicators. You can read more about how to use the water heater in the instructions.
Recommendations for choosing a mode
It is believed that by setting a low heating temperature, you can save electricity. This is not so, because the efficiency of the device decreases. When choosing a technique, pay attention to additional functionality. The saving function, which is indicated by the letter “E”, will be useful.
You need to understand that in this case we are talking about reducing finances for servicing the boiler. When the economy mode is turned on, the heating does not exceed 50 degrees. Scale is practically not deposited on the parts and walls of the tank.
Indicators below 50 degrees contribute to the growth of bacteria and microorganisms. Water acquires an unpleasant odor and color. How to clean a water heater, read in a separate article.
Why the equipment does not turn on
Did you start the instrument following the instructions, but nothing happened? It is necessary to check the network cable, socket, plug for serviceability. Also read the article: “Why does a water heater knock out an RCD.”
What could be causing the problem:
- Strong scale deposits on the heating element, its malfunction.
- Failure of the thermostat. It can give overestimated readings, which leads to the shutdown of the RCD machine.
- Empty tank, air left inside.
Before connecting, read the instructions and our recommendations. Improper operation can lead to damage to expensive equipment. If you are not sure about the installation ability, it is better to call a specialist.