How to protect the washing machine from leaks with your own hands

If your washing machine is leaking, you need to install a leak protector. We will consider all the options, and also talk about what Aquastop is in a washing machine and what programs are already installed to prevent leakage.

Why is the washer leaking?

Faced with such a nuisance, it is necessary to act quickly. If the leak is not fixed on time, you risk not only equipment breakdown, but also the repair of the premises – yours or the neighbors below.

There are many reasons that lead to a leak:

  • the use of low-quality detergents;
  • non-compliance with user instructions;
  • manufacturing defects;
  • damage to seals and pipes, etc.

The first thing to do when leaking is to stop the water and drain it from the tank. Only by shutting off the water supply valve and turning off the washer from the network, you can proceed to the inspection – to determine the location of the leak.

Reason 1. Hose

You need to conduct a thorough inspection of the water supply hose. Use ordinary toilet paper as a tester: it can be used to find all damage and leaks.

If it was the hose that was the cause, then the malfunction can be eliminated quickly and practically without cost:

  1. If a break is found where the inlet hose connects to the machine body, replace the gasket. At the same time, you can check the filter mesh for blockage.
  2. In case of mechanical damage, seal the puncture with a patch using waterproof glue. In this case, electrical tape will not interfere.

Important! The surest way to fix a breakdown is not to repair the hose, but to replace it.

Reason 2. Powder receiver

When water starts to flow in the machine immediately after it arrives, the reason may be the dispenser – the compartment for washing powder. For example, undissolved grains of powder can get stuck in it or sediment from dirty water can form.

In such a situation, proceed as follows:

  1. Pull out the dispenser and thoroughly clean all corners with an old toothbrush.
  2. Put the dispenser in place.
  3. Start the testing machine.

Water should not flow under high pressure, so if necessary, screw on the water supply valve.

Reason 3. Branch pipes

It is possible that the inlet valve pipes in your washer are damaged. In this situation, you will have to remove the upper part of the machine and replace the parts. If the problem lies in the pipes for collecting water, it is not necessary to change the part, it is enough to seal it well.

Important! The reason for the failure of nozzles is the austerity of manufacturers. Poor-quality products quickly lead to equipment failure.

Reason 4. Rubber cuff

Having found a water leak from the door, you can be sure that the rubber cuff designed to seal the door has been damaged.

Everything is very simple here: disassemble the door and remove the seal, seal it with a patch. With a large gap, it is recommended to replace the seal with a new cuff.

Reason 5. Drum

With frequent washing of shoes, clothes with metal products, the drum may be damaged. If you find this, contact a specialist who will replace the drum.

If you want to save money and try to replace the drum yourself, read our instructions.

Leak protection options

Many budget washers and mid-range machines do not provide protection against water leakage. What can happen to a machine that lacks protection?

In such models, the flow of water comes from the water supply through a flexible hose for the washing machine. Often they do not have a bottom, or it is covered with a plastic panel. When the inlet hose breaks, water collects and then flows to the floor.

In order not to make a flood, experts advise turning off the valve after turning off the washer. You can also install another protective system on your own using inlet hoses with valves.

But more expensive cars attract many buyers with protection installed from the factory. You can safely purchase the latest models of cars from brands such as Asco, Ariston, Bosch, Zanussi, Siemens, Electrolux, AEG, Miele.

Partial leak protection

Let’s understand how partial protection works.

Models providing such protection have a special pallet, inside of which a float with an electric switch is installed. When a leak occurs, water collects in the pan, when it reaches a certain limit, the float rises, affecting the switch.

The plus is that in the event of a leak, the washing machine automatically stops working, the drainage pump drains the water.

Important! You will know about the leak by the error code on the display. Eg, E1 code will appear in the ElG washing machine, in the Samsung brand model – E9.

If there is water in the pan of the washing machine, it is necessary to drain it, and then carefully inspect the equipment, finding the cause of the malfunction.

A washing machine with partial protection is a model in which operation is provided only when water flows into the appliance. In the event of a hose rupture, a flood is guaranteed anywhere. In such a situation, it is best for you to purchase inlet hoses with valves.

Hose types:

  1. The hose, complete with a block with a peephole, is connected to the water supply. Inside the block is a plunger, which is held by a spring. When the hose breaks, water enters, the spring weakens, and the plunger prevents water from leaking. The peephole turns red, warning of danger. Spring-loaded hose protection guarantees quick response, so you can prevent flooding and damage to the washer.

Important! Such a hose has one significant drawback – after it is activated and notifies of a leak, it will have to be dismantled.

  1. This hose, according to the principle of operation, is identical to the first type, the only difference is that several magnets are installed inside the block, turned to each other. Due to this, the plunger is held before the water flows into the protective block. This hose, like the previous one, must be replaced immediately after activation.
  2. Hose with solenoid safety valve. As long as the washer’s power cord is not connected to the mains, the plunger shuts off the water supply. When the machine is turned on, the valve opens.

Menalux protection is the installation of a special hose that guarantees reliability and prevents leakage.

Full protection against leaks – a guarantee of reliability and stable operation

In models equipped with full protection, the Aquastop system is provided with the following elements:

  • pallet;
  • float;
  • hose with solenoid valve.

The principle of operation of the system is to operate when:

  • great grandmothers;
  • rupture of pipes;
  • high level of foam formation, its exit to the outside.

In addition, an emergency operation occurs if the main and safety valve do not work. You can turn off “Aquastop” by installing a valve that automatically stops the water supply.

Conclusion: how to protect the car from leakage

If you are concerned about the problem of water leakage, it is recommended to purchase more expensive washing machine models that provide partial or complete overflow protection.

Only high-quality machines with positive reviews will cope with washing clothes and will serve you for many years without serious breakdowns and leaks.

Leave a Reply