Contents
After buying a washing machine, few people want to spend money on installation, which is obsessively offered by employees of household appliance stores. In this article, we will show you how to install a washing machine yourself.
First stage. Installation
You have received the long-awaited technique, now it’s time to move on to the installation. You will need to remove the shipping bolts located on the back of the machine body. Fasteners are necessary so that the tank does not dangle inside during transportation, as this can damage the “insides” of the equipment. The bolts will not allow you to turn on the machine, moreover, this can lead to serious damage. To avoid problems with removing the bolts, use a wrench or pliers. Close the holes with plastic plugs that come with the washer. Do not throw away the fasteners – they will come in handy in case of a move.
Recommendation! Read the instructions carefully before using your washing machine for the first time. This will protect the equipment from possible breakdowns and damage due to negligence.
Where is the best place to install SMA
It is not difficult to connect the washing machine yourself, but first you need to figure out where to install the equipment. The place should be such that in the future it would be convenient for the equipment to maintain and get to all the necessary details. Often, owners prefer to install the machine in the bathroom, as it is not only convenient and practical, but also goes well with any interior. But in this case, it must be borne in mind that high humidity can adversely affect the operation of the SMA. A washing machine is also installed in the kitchen. This option is quite acceptable, especially when there is not enough space in the bathroom. And in the kitchen, the machine can be built into a cabinet, hidden in a closet or installed in a niche. If desired, you can install the SM in the hallway, if there is enough space and there is a socket. Before installation, it is very important to think over everything, weigh all the pros and cons.
Hot water: yes or no
Today, some modern models of machines are suitable for connecting cold and hot water. But the opinion of experts boils down to the fact that when connecting hot water, no advantages are foreseen. Modern machines have a heating element that heats water to the desired temperature. But there are significant disadvantages:
- Water can be heavily polluted as opposed to cold. Therefore, you will often have to clean the filter of the filler valve (and the drain too). You will have to do this either on your own, or call the master, and this will hit the family budget.
- Hot water is very hard, so you have to use more washing powder. Otherwise, after washing, things will remain dirty.
If it is impossible to connect the washing machine to hot water, then there is no need to think about this issue.
Second phase. Water connection
Connecting the washing machine to the water supply is a process that requires special attention, accuracy and accuracy. If you do everything right, your machine will work properly. To connect the equipment to the pipeline, you will need flexible hoses with a diameter of 2 cm. To connect the washing machine to water, you must perform the following steps:
- Find the right place in the plumbing and cut the thread.
- What is needed to install a valve? Fasteners – they guarantee a secure fit.
- Install a protective mesh to prevent the penetration of small foreign objects inside the drum.
Advice! Clean the mesh and close the valve after each wash – this will ensure stable and efficient operation of the machine.
To supply water, you need a ready-made outlet that connects to a mixer or drain tank. Such a simple installation scheme will help you cope with the connection to the water yourself.
Third stage. Network connection
This process requires responsibility. It is necessary to install one socket, which must have protection against water and grounding. Most modern washing machines are often protected from current and have grounding. But it’s better to play it safe once again than to put your life in danger, and your equipment to failure. Basically, all machines have a power cord approximately 1,5 meters long. Therefore, the outlet must be at such a distance that you can connect the equipment to the network.
Recommendation! Do not use extension cords as they do not guarantee safety!
If this stage is completed without any difficulties, it’s time to move on to the final step.
Fourth stage. Fixing the machine
We continue with the installation instructions. Do not know how to install the CM so that there are no vibrations, jumps and shaking during washing and spinning? This problem occurs due to an uneven floor. The machine must be installed on a perfectly flat floor. If you find any irregularities, use a rubber mat – put it under the machine. The mat is excellent at absorbing vibrations. In no case do not use wooden linings or linoleum cutouts – they only temporarily eliminate the problem. Here’s a way to make sure the washer is installed correctly and at the right level: put your weight on each corner of the top cover. If none of them give way down, the machine is level.
Important! If you neglect the installation rules, the machine will start jumping during washing. This usually ends in failure.
The final stage. Testing
Have you coped with all the difficulties in installing the equipment with your own hands? Now it remains to evaluate the result of the work done – to make sure that everything is done correctly and the machine works as expected. The check goes like this:
- When you select the washing mode, the drum rotates, and does not stand still.
- There are no signs of leakage – the hoses are well connected.
- When turned on, there is no extraneous noise inside the machine.
- The correct operation of the spin cycle and the drain, which functions stably after washing, confirm the correct installation.
If you are interested in a visual detailed installation of a washing machine, a video instruction will help you figure it out:
Now you can check the effectiveness of washing clothes in the CMA. Good luck and enjoy using it.