How to decipher the error codes of the Vestel washing machine

Having problems with your washing machine? The self-diagnosis system will help you deal with them.

Vestel electronically controlled washing machines show an error code on the display. Electromechanical SMAs give an error by flashing indicators intermittently. For example, the code E02 can be defined as follows: the light bulb blinked twice, pause, blink again.

Fault codes specific to Vestel CM

The table shows the error values. Now you will learn how to fix the problem yourself.

Error code on the scoreboardPanel indicationValueCauses of appearanceHow to fix a problem
E01With error E01, the 1st and 2nd lights flash.Manhole door not tightly closed.
  1. The hatch lock is faulty or the handle is broken.
  2. The hatch blocking device (UBL) has failed.
What to do:
  1. Press the door firmly until you hear a click.
  2. Inspect the lock, tongue, door handle. Replace elements if defective.
  3. Check UBL, install a new part in case of breakage.
E02Code E02: the 1st and 3rd indicators blink.There is no water in the tank, or it has not reached the minimum possible level.If the code is displayed on the display of the washer, then:
  1. There is no water in the tap.
  2. There is a blockage in the drain system.
  3. Inlet valve defective.
How to troubleshoot:
  1. Turn the shut-off valve, it may be closed.
  2. Clean the inlet hose, mesh filter, inlet valve from clogging.
  3. Replace fill valve if defective.
E03The 1st and 4th lights on the panel flash.Pump error.Why is the E03 code on:
  1. Clogged drain filter or pump.
  2. Broken wiring.
How can I remove the error with my own hands:
  1. Clean the drain filter and pump from clogging.
  2. Check wiring, isolate damaged areas, replace cable.
E04The 2nd and 3rd indicators blink.What does the combination mean: overflow of water.If the error code E04 is displayed on the CMA display, there is too much water in the tank.The system should automatically drain excess water.
E05How to recognize the E05 code: the lights under numbers 2 and 4 are flashing.Faulty heating element or thermistor.The heater of the Vestel washing machine burned out or suffered from scale.To reset the error, do this:
  1. Test the operation of the heating element with a multimeter. Clean it off. In case of malfunction, replace the element.
  2. Inspect the temperature sensor for serviceability. Install a new part.
E06Error indication E06: 3rd and 4th lights flash.Motor malfunction.The cause of the malfunction is a breakdown of the motor or its components.To solve the problem, it is necessary to replace the motor electric brushes or install a new motor.
E07The E07 code manifests itself as follows: the 1st, 2nd, 3rd indicators blink.What does the error mean: a malfunction of the electronic control unit.If the Vestel washing machine gives this error code, there is a problem with the control board.How to fix the crash:
  1. Test the board to see if it works.
  2. Engage in repair or replacement of the board. But it is better to contact the service center.
E08In the event of a malfunction E08, the 2nd, 3rd and 4th lights flash.The SM motor is out of order.The motor is defective.Checking and changing the engine of the Vestel washing machine.
E09How to recognize the E09 code: the 1st, 2nd, 4th lamps are flashing on the panel.Electrical error.Cause of the problem: the mains voltage is not correct.Too high or too low voltage will prevent the CMA from working properly. You need to wait for the voltage to normalize or call an electrician.
E10With error E10, the 1st, 3rd, 4th lights blink.Communication problems.There were problems with the communication system.Restart the washing machine for 15-20 minutes. If, when you turn it on again, a malfunction is displayed again, it is better to turn off the water supply and call the wizard.

After reviewing the typical breakdowns of Vestel washing machines, you can solve the problem yourself or contact a service center.

Leave a Reply