Washing machines today have replaced manual labor for many housewives. In order for them to wash effectively for many years, you need to regularly care for them. To prevent breakdowns, protect mechanisms from serious consequences, extend the service life, carry out preventive cleaning.
Most housewives forget that water remains in the gum of the washing machine, so it needs to be cleaned systematically, from time to time.
Next, we will talk about how to properly clean the rubber seal in the washing machine.
Choosing cleansers
If you notice that the gum in the washing machine has turned black, first find the source of the fungus infection. Check the cuff and, if an infection is found there, proceed to cleaning using a pre-selected product.
Not sure how to remove mold from washing machine gum? Most housewives use such means:
- chlorine;
- acetone;
- soda.
If you are more concerned about the question of how to clean the cuff of the washing machine from scale, use proven products with positive reviews. These include:
- citric acid (ordinary, food);
- 9% vinegar;
- special means Anti-scale.
How to properly clean gum
In order for the drum of the washing machine not to become moldy and the smell of rot does not appear in it, do not close the hatch door tightly – the drum will be ventilated. Wipe the detergent drawer with a dry cloth after every wash.
So, you have repeatedly had the question of how to clean the gum in the washing machine – we will tell you how to do it. Follow the instructions below step by step:
- Wipe the outside of the gum with a damp cloth.
- Repeat the procedure inside the gum. There most often “sits” mold.
- Soak a sponge in bleach and wipe the entire circumference of the drum. Apply as much bleach as possible to the rubber seal.
- Close the door and leave for 30 minutes.
- After the procedure, turn on the washing machine for rinsing.
How to clean the cuff of the washing machine from mold – be guided by proven methods:
- Prepare a solution of 2 cups of vinegar. Pour under the seal, select a long washing mode, start and turn on the “pause” after five minutes. After an hour, washing can be continued. During this time, the vinegar will even get into the far corners of your washer, including under the cuff. After that, rinse the substance with water and wipe with a dry sponge. For better washing out of the remnants of the solution, use the quick wash mode.
- Apply citric acid. Mix 60 g of powder with a little water. Take your toothbrush and clean the gum thoroughly inside and out. Then turn on the “idle” mode for a short time.
- To remove mold with acetone, apply a little solvent to a cloth and wipe the cuff thoroughly, then rinse with water. This method will also help get rid of unpleasant odors.
Important! Do not forget to wipe moisture from the seal after each wash. Keep your cuff clean and you won’t have to clean it!
Mold and debris accumulated under the cuff leads to fungi. Knowing how to remove the fungus in the washing machine will allow you not only to remove the infection, protecting the CM from breakdowns, but also to maintain health.
First of all, you need to remove the rubber seal completely – this is quite simple to do. You will have to pick up the wire clamp holding the rubber band with a thin screwdriver and carefully remove the clamp, leading the screwdriver in a circle. After that, you can safely remove the seal – do it carefully so as not to damage the gum!
Then wash the rubber in a large container with water and bleach. Let the cuff dry before reinstalling.
Important! Be careful: by removing the cuff, you will have access to the UBL (electronic door lock). Be careful not to snag the wiring and the device itself so that you do not need repairs after such cleaning.
No to mold!
How to wash the gum in the washing machine, we have already figured out. Now consider the recommendations that will help prevent the appearance of mold in the washer, or rather under the rubber cuff:
- Do not use a washing temperature below 95 degrees. Even if you do not need to wash your clothes, try to run the “idle” program at least a few times a month for the longest time.
- It is forbidden to use gels, since the inner walls of the machine are covered with them, creating a breeding ground for fungal formations. Use conditioners or washing balms as little as possible.
- Remember to wipe the powder container with a dry cloth. It is better to wash the tray with chlorine and dry before installation. If the container is not removable, cleaning with soda is recommended.
- Remove the laundry from the drum as soon as the washing cycle is over.
- It is necessary to descale the machine at least once every six months using vinegar and citric acid. To prepare the composition, mix vinegar and citric acid in a ratio of 1 liter per 400 g.After that, start the longest program with a temperature not higher than 65 degrees.
- Occasionally thoroughly clean the filters and hoses from accumulated dirt.
Having found damage on the cuff, replace the seal with a new one! If you can’t do it yourself, contact an experienced washing machine repair technician.
When loading the next dirty laundry, you will not feel the “aromas” and forget forever what is the dirt in the washing machine under the rubber band.
Now you know how to wash the gum in the washing machine. In order not to have to change the cuff, to protect it from damage, to avoid the appearance of mold and mildew, follow the recommendations described above.