Contents
*Overview of the best according to the editors of Healthy Food Near Me. About selection criteria. This material is subjective, is not an advertisement and does not serve as a guide to the purchase. Before buying, you need to consult with a specialist.
An unpleasant yellowish coating on the surface of the bath appears, as a rule, due to low-quality soap or detergent. It settles on the enamel, after which it dries up and enters into chemical reactions. However, it can be washed off.
And in this article we will talk about how to clean the bathtub white without damaging the coating. Tips are suitable for all types of baths.
How to clean a white bath using special products
The easiest way is to use special bath cleaning products. They contain components that destroy both mineral and fatty deposits. Cleaning and bath products can be purchased at household chemical stores.
Read the instructions before using this tool. It may be necessary to pre-dilute it with clean water – if the drug was supplied in the form of a concentrate.
Folk remedies for cleaning white bathtubs
You can clean the bath not only with special, but also with folk remedies. As a rule, they are in every house (except, perhaps, soda ash), so you don’t have to go to the household chemicals store.
In the fight against yellowish or matte white plaque will help:
Vinegar. Fill the bathtub with warm water slightly above the usual level. Add 1 cup of food grade white vinegar and stir. Leave for 3-4 hours. After that, drain the water and wipe the surface dry;
Lemon acid. Vinegar can leave a bad smell in the bathroom, so it can be replaced with another agent. Fill the bathtub with warm water slightly above the usual level. Add 100-150 grams of citric acid and stir until the powder dissolves. Leave for 3-4 hours. After that, drain the water and also wipe the surface dry. Use soft wipes so as not to scratch the enamel;
Chlorine bleach. The most effective way to make the surface shiny, even if not too long-term. Fill the bathtub with cold water above the usual level. Add 200-500 ml of chlorine-based bleach (“Whiteness”) depending on the volume of plumbing. Leave for 4-8 hours. After that, drain the water and rinse the walls of the bathroom thoroughly, and then wipe it with a dry soft cloth;
Soda ash and baking soda. In addition to bleaching, these products have an antibacterial effect. Mix 2 tablespoons of soda ash and baking soda. Dilute with water to form a mushy paste. Rub the bath with the mixture. Leave for 10 minutes. Mix 50 ml each of vinegar and chlorine-based bleach. Apply over a layer of soda. Leave for half an hour, then rinse the bath very thoroughly;
Baking soda and citric acid. It will also help restore a bright look and get rid of bacteria. Mix half a pack of baking soda with water until it becomes a paste. Apply the mixture on the walls of the bathroom and leave for 30-60 minutes. After that, dissolve 200 grams of citric acid in a small amount of water. Soak a sponge in it and wipe the surface of the tub. Then rinse thoroughly with water.
When working with baking soda, vinegar, citric acid, and chlorine bleach, be sure to use rubber gloves to protect your hands. You can also wear a mask or respirator to avoid respiratory damage (especially important for people with asthma).
Make sure the bathroom is well ventilated when using chlorine bleach products. Ideally, if it is active. You can also just put a fan. After using chlorine bleach products, leave the bathroom aired out for at least XNUMX hours by showering, doing laundry, and brushing your teeth somewhere else. This will help protect the eyes and mucous membranes from the caustic action of the substance.
How to remove stubborn dirt from bathtubs
You can remove stubborn dirt from the surface of the bath with ammonia. It is effective in the fight against a variety of stains.
It is worth noting that this procedure requires good ventilation of the bathroom. Otherwise, the smell of ammonia will remain in it for a long time, “corroding” the nose and mucous membranes.
The procedure is simple:
Mix 20 ml of ammonia and 200 ml of water;
Dip a sponge into the mixture and apply to the walls of the bath;
Leave for half an hour;
Wash off with plenty of running water.
Work must be carried out with rubber gloves. Optionally, you can wear a respirator and goggles – they will help you feel more comfortable when applying ammonia to the bath.
How to Remove Rust from a Bathtub
To remove traces of rust, you will need to use an acid agent. For example, salt, vinegar, citric acid, or Coca-Cola:
Vinegar. Sprinkle the rust stain with regular table salt. Soak a cloth or tissue in 9% white vinegar and lay it on top of the stain. Leave for 1-2 hours. After that, the rusty stain can be wiped off with a sponge;
Lemon acid. Mix salt and citric acid. Pour onto stain. Soak a washcloth in warm water and place over the stain. Leave for 1-2 hours. After that, the stain can be wiped off with a sponge;
Coca Cola. Use the original drink, not an imitation. Soak a tissue or cloth liberally in Coca-Cola, and then place it on the stain. Leave for a few hours. Periodically add “Cola” from above to avoid drying out. After that, the rust stain can be wiped off with a sponge.
Work with salt, vinegar and citric acid is recommended to be carried out with gloves. Otherwise, irritation may occur, especially at the sites of skin damage (scratches, abrasions, pimples).
Attention! This material is subjective, is not an advertisement and does not serve as a guide to the purchase. Before buying, you need to consult with a specialist.