The self-diagnosis system of Haier washing machines, when a problem is found, displays a fault code on the panel. In electronic models, the error is shown on the display or on the scoreboard; on washers without a screen, the indicators will flash. Therefore, it is easier for you to understand the causes of the problem, you just need to understand the meaning of the code.
After reading the material, you will save time on diagnostics and find out: what the error code means, what to do when it appears. And also how to fix, or fix the breakdown with your own hands.
Short circuit – short circuit.
SM – washing machine.
SMA – automatic washing machine.
ERR1 (ERR1) Program failure. Malfunction with the hatch blocking device (UBL), the door lock is broken.
1. Replacement of UBL.
2. Installation of a new lock.
ERR2 (ERR2) CMA Hyer water drain error. Timeout expired (drain time exceeds 4 minutes). Clogged drain system CM.
1. Cleaning the drain hose and filter.
2. Check and replace the drain pump.
3. Checking the pressure switch, installing a new part.
4. Repair of contacts of the electronic block.
ERR3 (ERR3) Error ERR3 reports a problem with the thermal sensor. Water is not heated in SM Hayer. The thermostat has failed. Temperature sensor change. ERR4 (ERR4) Problems with heating. The water does not heat up to the set temperature. Malfunction of the heating element (heater). The solution to the problem is to replace the heating element. ERR5 (ERR5) Problems with the collection of water in the Hayer washer.
1. Low pressure.
2. The water tap is turned off.
3. Clogged inlet filter.
4. Violation of the wiring between the control module and the pressure switch, pump.
1. Check the pressure in the water supply.
2. Turn off the tap. Perhaps it is not completely open or blocked.
3. Rinse the strainer of the intake valve.
4. Replace defective contacts.
ERR6 (ERR6) If CM Hyer issues an ERR6 error, then there is a problem with the control module. Defective control board, broken contacts, wiring. The control board is inspected for damage. It is necessary to tightly connect the connectors, isolate the defective areas. ERR7 (ERR7)
The electronic unit is defective.
Attention, critical code!
The unit could fail due to a short circuit, or from prolonged use of the machine in a humid room. The electronic unit needs to be replaced. ERR8 (ERR8) If the code ERR8 is on the screen, it means that there is a problem in the water intake system.
There is more water in the tank of the Haier washing machine than is needed for washing.
1. Malfunction of the pressure switch (water level sensor).
2. Breakdown of the electronic controller.
1. It is necessary to replace the level sensor.
2. Repair of the electronic control unit and its contacts.
ERR9 (ERR9) The code ERR9 was displayed on the panel. Problem with water intake in SM Hyer.
The tank is full of water.
1. Breakage of the water supply valve.
2. Problem with the control board.
1. Check, change the intake valve.
2. Diagnostics and installation of a new electronic board.
ERR10 (ERR10) An error occurred during water intake. It is possible that the pressure switch is broken. Troubleshooting the pressure switch. Installing a new part on a Hyer washing machine. ERR13 Engine problem The motor is out of order, there is no voltage on the windings. Check the electric motor: brushes, winding. Repair or replacement depending on the nature of the damage. UNB (YUNB) Uneven arrangement of things in the drum of the Hayer washing machine. Imbalance. When washing, things got lost in a lump, the balance was disturbed. To remove the error, you need to stop the CM Hayer and manually distribute the laundry. EUAR (EUAR) Error in the electronic board. Violation of the circuits of the electronic unit.
1. Check wiring for defects and damage, repair defective areas.
2. Repair or replacement of the controller unit.
NO SALT Incorrect composition of detergent for CM Hyer. There is no powder in the tank, or its composition is not suitable for washing.
1. Check the dispenser to clear the error.
2. Add washing powder.
3. Inspect the powder entry channels into the tank, clean them.
4. Select a wash cycle without detergent.
Now you know what the fault codes in the Hyer washing machine mean. You have the opportunity to independently diagnose the problem and carry out repairs yourself.