Contents
The gas boiler “Conord” is a product of a domestic manufacturer. The boilers are guaranteed for 3 years, and the expected duration of operation is up to 25 years. The brand offers equipment for both heating and combined.
About Us
The production facilities of the Russian brand “Conord” are located in Rostov-on-Don. Gas heaters have been produced here since the seventies of the twentieth century. Today it is a leading Russian manufacturer whose product quality is based on a large-scale modernization of production. Instead of old machines, European lines were launched – Swiss and Italian. The cost of manufactured heaters is much lower than European ones – in the range of 15-50 rubles.
CONORD is not just a name, consonant with the name of a large eagle, it is an abbreviation. It is deciphered as follows: Heating boilers of non-standardized equipment Rostov-on-Don. The first heating boiler produced by the enterprise is DON-16.
Advantages
After reading reviews about the products of the Rostov enterprise, it is easy to understand that it is in high demand. The Russian consumer is attracted to Conrod products by:
- Cost – prices for Russian products are much lower than for European ones. Sometimes the difference is 50%. The cheapest 8 kW models used for heating a private house cost only 15 rubles.
- Long term warranty. The manufacturer guarantees trouble-free operation for fifteen years.
- Not dependent on electricity. A shutdown, especially in winter, due to a lack of electricity, is almost a disaster. Therefore, for volatile equipment, it is necessary to install backup power – a generator or a battery. There are no such problems with Conord.
- Ease of operation. The abundance of functions, electronics and automation from other brands often causes unnecessary trouble.
- Silent work.
- High-quality assembly.
- Good technical characteristics: Rostov boilers are practically not inferior to foreign analogues in terms of productivity, efficiency, and heating rate.
- High efficiency – about 90%.
Design features
- Convenient adjustment. Heating is adjusted by a mechanical rotary regulator, which allows you to change the strength of the fire.
- Simple ignition – no complex automation, which often makes you nervous in imported analogues.
- Due to its special design, the cold-rolled steel heat exchanger is resistant to overheating, which can significantly increase the service life.
- The burner is able to function even at the smallest gas pressure.
- Low heat loss – there is thermal insulation of the body.
- Dimensions are modest. Floor-standing devices are always larger than mounted ones, but Conord’s dimensions are quite acceptable for small rooms. Stylish design – easily combined with modern interiors.
- The body is lined with steel sheets (thickness 3 mm): thanks to the powder coating, they are characterized by increased heat resistance.
- The flame of the burner is modulated automatically – the device is economical and efficient.
- A transition to another fuel is provided.
- The security system protects the device from emergencies.
What are they
If you are interested in the products of the Rostov manufacturer, you can choose a boiler from four series.
- With Italian automatics SIT: KSts-G-S / KSts-GV-S – single-circuit / double-circuit.
- With thermohydraulic automatics: KSts-G-N / KSts-GV-N – single-circuit / double-circuit.
The manufacturer offers heating boilers with two types of heat exchangers: steel and cast iron. All gas heaters produced by the Rostov enterprise are floor standing only. If you are interested in a wall-mounted unit (with a closed firebox), you will have to turn to another brand.
Steel
Heaters with steel heat exchangers have the following advantages:
- Steel is more ductile than cast iron.
- The specific gravity is less.
- High heat dissipation.
Minus one, but very important – low resistance to damage and corrosion. That is why consumers who know a lot about materials choose cast-iron counterparts. Manufacturers try to minimize the disadvantage by using resistant coatings, but they cannot provide 100% corrosion protection.
Cast-iron
The main advantages of cast iron heat exchangers: high thermal conductivity and resistance to corrosion.
Cons:
- Cast iron is less flexible and ductile than steel – not as resistant to deformation.
- Inferior to steel in strength.
- Brittleness is the main disadvantage of cast iron. Particularly dangerous situations arise during transport and installation, which is why installation should be entrusted to specialists. After delivering the device home, be sure to check the integrity of the cast-iron heat exchanger. Even the presence of microcracks is the most dangerous situation for equipment. If they appear, the equipment will soon fail, and the heat exchanger will need to be replaced.
Secrets of High Performance
Modifications with thermohydraulics are non-volatile. The principle of operation is based on the use of a thermostat. When the temperature reaches the declared value, the gas supply to the burner stops. This maintains the required heating of the coolant.
The devices are ideally adapted for harsh winters: they can stably keep the required heat, the main thing is to correctly calculate the power. Efficiency is increased by:
- modulating burner;
- obtaining the optimal composition of the gas-air mixture;
- leaving the bulk of the heat to heat the coolant.
How to decipher the symbols
For example:
- KSc-GV-12
- KSt-G-10S
“K” is the boiler. “C” – made of steel. “C” – a cylindrical firebox. “G” – gas. “GV” – heats the water. The number is the maximum power.
How to choose the right performance? For 10 sq.m you need 1000 W (ceiling height 2,5 m). This formula is suitable for rooms with medium heat loss.
Safety system
The manufacturer has provided reliable protection:
- The smoke sensor, reacting to the lack of draft, stops the gas supply. Will not allow the burner to go out if there is a reverse draft due to strong gusts of wind.
- Fire control. If it is not there, the gas will not flow.
- Temperature control. When a certain value is reached, the heating of the coolant stops.
How they work
The fire chamber is made of steel sheets of 3 mm. There is a water jacket, a gas burner unit and smoke tubes with turbulators that increase the efficiency of the device. The gas burner unit works automatically – the power is modulated. Basalt cardboard was used for thermal insulation. There is a thermometer – visually control the temperature of the water.
If the model is 2-circuit, then the chimneys are equipped with a DHW coil. The input-output of the latter is located on the rear panel of the case. The diameter of the nozzles is 2 inches / 5 cm. For hot water supply – 0,5 inches or 1,5 cm. Devices with a power of 8-12 kW have a chimney with a diameter of 11,5 cm. 16 kW – 15 cm. There are modifications with and without circulation pumps .
Important! The system coolant is plain water, antifreeze is prohibited.
How to keep the warranty
In order not to be denied warranty obligations, you should not take on installation and adjustment work. Connection, configuration, first start-up are carried out by the specialists of the service center. They also make a record of the work done in the passport of the device. Preventive maintenance should be carried out annually – it is also noted in the data sheet. If there are no such records, the warranty will be void.
The instruction and connection diagram are given for review. Their presence in the configuration does not mean that the owner of the equipment can connect it himself.
The nuances of editing
Owner reviews confirm that Conord may go out. Provoking factors:
- Burner dirty. Before turning on the device, clean the nozzles with a brush or vacuum cleaner.
- Not enough oxygen to start the burner. It is necessary to clean the nozzles supplying air and ventilate the room.
- The thermostat contacts are oxidized. Need to clean up.
- The sensors are broken.
With a strong cooling of the coolant, you need to switch the thermostat to the maximum or increase the flow of gas to the burner, if the instruction allows such an action.
Summer use features
In the summer it is necessary to turn off the heating circuit. To do this, close the valve at the coolant inlet. With one pilot burner, the water will heat up to 60 °C in 60 minutes. If the water is not consumed, it will retain heat for about two hours – it can be used for domestic needs. When the device heats up, and active consumption of water is not expected, it is turned off so that the water does not boil.
Models overview
The manufacturer produces 4 series, differing in design features and characteristics.
KSc-G-S
Single line models. Automation – SIT. Power range: 8-30 kW. Temperature range: 60-90°C. Pressure 0,2-1,9 bar. The price depends on the power – 15-23 rubles. They heat buildings of 000-80 sq. m.
Characteristics and design features of one of the modifications of the series – KSts-G-20 S:
- Convection. One circuit. Open firebox.
- Non-volatile.
- Heat output – 20 kW.
- Area – up to 200 sq.m.
- Efficiency – 90%.
- Price – 21 rubles.
- Weight – 51 kg.
AOGV-11.6-3
- Convection. One circuit. Open firebox.
- Non-volatile.
- 11 kW.
- Area – up to 116 sq.m.
- Efficiency – 90%.
- The price is 15 rubles.
- Weight – 33 kg.
KSts-GV-12S
Outdoor, like all Conords. KSC 12 S has two circuits. Mechanical control. Characteristics:
- Heats up to 120 sq.m.
- Up to 12 kW.
- KPD — up to 90%.
- Weight – 39,5 kg.
- Fuel (gas) consumption – 1,35 cubic meters / h.
KSc-G-N
Models of this series are with one circuit and hydraulic automatics. 10-30 kW. convection type. Open firebox. The material of the heat exchanger is cold-rolled steel. The maximum pressure is 5 bar. The price is about 12 rubles.
Characteristics of modification KSts-G-12N:
- Heats up to 120 sq.m.
- Up to 12 kW.
- KPD — up to 90%.
- Weight – 39 kg.
The KSts-GV-S series are also produced – double-circuit with SIT automatics, KSts-GV-N – also 2 circuits, with thermohydraulic automatics.
KS-G-P 7S-16S
Parapet modifications can be placed even in an apartment.
- 60-140 m².
- 7-16 kW.
- Closed furnace.
- Weight 45-67 kg.
- 22-27 rubles.
Reviews
“Conord Comfort”: Alexander L., Smolensk.
Inexpensive model, works only for heating. I prefer a separate boiler to fuss with two circuits – I don’t believe in the stability of hot water when it comes to domestic boilers. There is no money for imports, and even there there are enough problems with automation. Corresponds to its value. Heats the house 120 squares. Economical – gas is consumed sparingly. Of the minuses – it is not convenient to kindle the wick. A flexible hose is also inconveniently connected, it would be better if it was placed on the left.
KSts-G-12N: Viktor E., Tver
Simple single-loop without any programming. Good price and minimum hassle. It is non-volatile, but when the light goes out, it turns off, as our heating circulation pump turns off. Shutdown due to overheating. But this happens very rarely. Another problem is ignition. When you kindle, you need to keep the button pressed for a long time – your finger gets tired. It’s been running for two seasons now. It was difficult only at 30 degree frosts.
CONORD equipment is only for outdoor installation, so it is more often bought by owners of private houses and cottages. All models are affordable, simple in design and do not depend on electricity. They are easy to use. The brand has long gone beyond the domestic market, and offers gas appliances to consumers in the near abroad – they compete with imported counterparts.