Frequent malfunctions of Electrolux washing machines

Electrolux washing machines are popular with buyers. Modern models have wide functionality and convenient control, but at the same time they are in an affordable price segment.

Unfortunately, technology does not last forever. When a problem occurs, you have a choice: either contact a service center, or try to repair the Electrolux washing machine yourself.

Typical malfunctions of SMA Electrolux

To determine the malfunction, it is not always necessary to disassemble the Electrolux washing machine; it is enough to pay attention to the behavior of the SM during operation.

We will understand the causes of breakdowns that are inherent in the Electrolux Intuition washing machines (Electrolux Intuition), Electrolux Inspire and other models.

SMA does not turn on

You decide to start washing, but the machine does not turn on? Don’t panic. Let’s understand the reasons:

• Perhaps there is no voltage in the network, or it is not enough to start the SMA. How to check it? It is enough to connect any household appliance to the outlet. If the device works, it means that the problem is not in the network. If not, then you can call an electrician or wait for the power to come on.
• Defective power cord. Carefully inspect the cable and plug for damage. If there are any, you need to replace the cord.
• Check the manhole door. Perhaps it did not close before the click, so the process does not start.
• The contacts of the start button are oxidized. To check, you will have to remove the control panel and do the repair yourself.
• Problems with the main module. The failure of the control board is a serious matter. Sometimes a professional handyman may be required.

Problems with the supply and discharge of water in the Electrolux car

It happens that the Electrolux washing machine does not fill or drain water. Why is this happening:

• Weak water pressure. Inlet valve not open properly.
• The water intake hose is kinked. We need to inspect it and restore the work.
• The inlet valve, which is responsible for supplying water to the system, could fail to work.
• A mesh filter is installed in front of the inlet valve, which protects against the penetration of small particles from the water supply. It needs to be cleaned up. This can be done under the pressure of water.
• Washer pump failed. In this case, the water will not drain.
• Drain pipe clogged. Water does not drain due to clogging. The drain system needs to be cleaned.

No powder intake

After pouring the powder into the dispenser tray, the machine sends a jet of water through a special valve. Detergent comes out with the water. Over time, the SM may stop picking up the powder.

What caused the malfunction of the Electrolux washing machine?

The most common cause of the problem is a clogged dispenser. To eliminate it, just remove the tray and rinse under the tap.

If everything is in order with the tray, the inlet valve is likely to be worn. Then it needs to be replaced.

Washing in the Electrolux machine does not start, the drum does not spin

With such a problem, you can try to fix the problem yourself.

To do this, you need to open the hatch of the Electrolux washing machine and get half of the laundry. Having thus reduced the load, try to start the SM again. If there is no result, then:

• There is probably a problem with the engine of the car. The drive belt could be worn or loose, or the electric brushes were worn out. It happens that the engine burns out due to a short circuit.
• Breakage of the elements of the main board can lead to the failure of any part of the washer. Additionally, you can check the wiring between the module and the motor.

No water heating in Electrolux washing machine

How can you tell if your CMA is not heating water? After starting washing, wait 15-20 minutes. Then put your palm on the hatch glass. Warm surface – there is heating. And if washing takes place in cold water, the reason for this is a malfunction of the heating element.

The thermostat or voltage stabilizer could also fail.

Rinse does not turn on

Washer Electrolusk with vertical (front) loading did the wash as usual, but does not enter the rinse mode? Most likely, the heating element (heater) has broken. Since the water does not reach the correct temperature, the rinse does not start.

The cause of such a breakdown could be the control module. If a system failure occurs, it is enough to restart the SM within 15-20 minutes. If this happens all the time, you will have to replace the module.

The inclusion of SM Electrolux leads to knocking out traffic jams

When you turn on the washer, did the automatic box knock out? This means there is a problem with the power supply. Never restart an Electrolux machine. It’s best to call an electrician to find out what the problem is.

What can cause a blockage:

• Breakdown on the heater body.
• Oxidation of the contacts of the start button.
• Electronic board failure.
• Moisture entering the electric motor, causing a short circuit.

Spin does not work

Why won’t my Electrolux washing machine spin laundry?

• The tachogenerator, which controls the number of engine revolutions, has failed.
• Motor failure.
• The pump broke down, which is why the water does not drain.
• Motor failure or brush wear.
• A failure of the pressure sensor also leads to a similar malfunction. Since the water level in the tank is not detected, the machine cannot change to another mode.

Electrolux hatch door won’t close

Subsequently, the Electrolux washing machine does not start work.

• Check the handle and door lock for proper operation.
• Check the UBL device (electronic lock).

Fault codes Electrolux

The self-diagnosis system allows the user to determine the cause of the malfunction. When a fault code is displayed on the display, you just have to find out its meaning. Then the troubleshooting will be quick.

Consider the main Electrolux error codes:

Do-it-yourself Electrolux car repair

Having considered the malfunctions of Electrolux washing machines, we will also analyze their elimination.

Turn on problems

In order to solve the problems of knocking out traffic jams and lack of connection, you need to carry out repairs with your own hands. If you decide to check the contacts of the start button, do the following:

1. Disconnect the Electrolux washing machine from the mains.
2. Remove the top panel by unscrewing the fixing screws at the back.
3. Remove the dispenser tray by pressing the lock in the middle. At the same time, check the tray for clogging and rinse under the tap.
4. Behind the tray are fixing screws that need to be unscrewed.
5. Unfasten the latches and remove the control panel.
6. Connect the multimeter probes to the contacts of the button. Measure resistance.
7. If the contacts are damaged, they will have to be soldered, and then the panel should be replaced.

Also check the network filter. Additionally, remove the rear panel by unscrewing the fixing bolts. Inspect the wires and the filter itself for damage. Perhaps some contacts are burned out.

If there are no obvious breakdowns, disconnect the filter contacts and test them with a multimeter.

How to replace a faulty filter, see the video:

Problems with the intake and discharge of water

The cause of the tank filling problem in the Electrolux washing machine may be a blockage in the inlet hose or filter. How to clean the system yourself:

1. Disconnect the SMA from the network.
2. Shut off the water supply.
3. A hose is connected to the back of the washer.
4. Unscrew its nut, after substituting a container for water, which can spill out of the hose.
5. Then disconnect the other end of the hose connected to the faucet.
6. Inspect it for blockage, rinse under pressure with water.
7. A filter is located at the junction of the hose with the machine. It is a fine mesh.
8. Remove the filter and also clean it from blockage.

The design of the Electrolux washing machine is such that a drain pipe is provided for the normal drainage of water. If there are problems with the drain, you need to inspect and clean the pipe. A small do-it-yourself repair, or rather cleaning:

• Disconnect the machine from the network and communications.
• Lay it on its side so that you can reach the nozzle through the bottom.
• Wring out a collar of a branch pipe from a tank to the pump.
• Loosen the bolt holding the hose clamp to the tank. Disconnect it.
• Unscrew the pressure sampling chamber.
• Now disconnect the last clamp and remove the pipe.

Check it for blockage. Clean if necessary.

You also need to check the drain pump, a breakdown of which can lead to a problem with draining and spinning. See the video for more details:

The drum does not rotate

Do-it-yourself Electrolux washing machine repair with vertical or front loading. To do this, check the engine drive belt.

It could weaken and slip – then you have to put it back in place, or it could wear out – then a replacement is necessary. This simple repair can be done by hand:

1. After you have disabled the CMA and removed the back panel, you will see if the belt is in place or not.
2. To install the belt, slide it over the motor pulley.
3. Then spread over the drum pulley.
4. Gently rotate the pulley, distributing the belt.
5. Replace the cover and fasten the screws.

The cause of this malfunction may be the engine itself. How to check its performance, look at the video:

Heater failure

If the Electrolux washing machine does not heat water or does not start rinsing, the heating element is probably broken. How to make a replacement:

1. Unplug the machine and remove the back cover.
2. Below you will see the exits of the heating element.
3. Disconnect all wires.
4. Loosen the central nut.
5. Push the bolt inward and, gently prying the heater with a screwdriver, remove it.
6. Installation of a new element is carried out in the reverse order.

How to check the heating element for serviceability is described in detail in the video:

Washer door malfunction

We already wrote above why the door may not close.

Immediately check the tightness of the closure by pressing the sunroof with your hand. Then inspect the handle and mechanical lock for serviceability.

UBL, electronic lock could also fail. The video shows how to replace the UBL with your own hands:

Noisy Electrolux machine

During operation, the machine began to make a lot of noise and rumble. This is a sign that the bearings are failing. Not everyone can change them, because you need to completely disassemble the Electrolux washing machine.

Video to help you:

Now you know how you can repair the washing machine yourself. It remains to wish you good luck!