Float for long casting: selection rules, equipment options

Fishing with a float is possible not only close to the shore, but also at long distances that are beyond the capabilities of a conventional float rod. To do this, the classic fishing rod is armed with special elements that allow you to cast tackle over a considerable distance. Of course, such gear is not a competitor to feeder gear, but its capabilities are much higher compared to conventional float gear.

Distance detection

According to some anglers, there is no such definition. Unfortunately, one can both agree and disagree with this, since this concept is purely conditional. On the other hand, this distance lies within the casting range of a conventional float rod and a rod with a feeder. For each specific case, it may be different depending on the fishing conditions, which requires the use of gear with a certain equipment.

In order to cast the bait a considerable distance, as fishing conditions require, a regular rod will have to be equipped with a non-inertial reel and a heavier float, as well as a heavier sinker.

What factors affect the casting distance of a rig?

There are a number of factors that affect the casting distance of a lure. For example:

• Rod length. Almost everyone understands that the longer the rod blank, the further you can cast the bait. Although everything is not so simple here either, because it is not so convenient to work with a long rod, and the load on the hands is significant. Therefore, this factor should not be pursued. For an angler with a height of 180 cm, it is enough to arm yourself with a rod no longer than 4,5 meters long.
• Stroy rods also matters, but it is not as important as in the case of spinning fishing. It is believed that soft rods allow you to cast light lures over much longer distances.
• Line thickness. This is an important factor, which is limited solely by the size of the fish that is supposed to be caught. The thinner the line, the less resistance it has when the bait is flying in the air, which means that the rig will fly a little further. But even here there is a “but”. Too thin fishing lines are not reliable, as they are torn during casting, because they cannot withstand loads.
• Application of shock leader A must for long distance fishing. Its thickness ranges from 0,18 to 0,22 mm.
• Float shape. In such cases, floats with good flight characteristics are used. They are distinguished by an elongated body, consisting of one third of the thickened part, and the remaining two thirds is a thin tip, in the form of an antenna.
• The nature of the shipment. The more competently the load is distributed on the equipment, the further you will be able to cast the rod. As a rule, sliding types of weights are more optimal, since during the flight they move closer to the leader.
• Coil. The use of modern inertial-free reels, which are easy to use, allows for long-distance casts, due to the rapid descent of the line from the spool.

If you take these factors into service, then you can equip the rod according to all the rules for catching fish in long-distance casts.

Equipment float rod for long casts

To begin with, it makes sense to consider the construction of equipment, using blind mounting. Sliding installation, although it has differences, but very minor.

Tackle for long-distance casting is assembled in this order:

1. First you need to purchase all the necessary equipment, including a rod, up to 4 meters long.
2. A reel of size 3000 is attached to the blank of the rod, no more.
3. A fishing line is wound on the reel, about 0,18 mm thick.
4. The line is passed through the guide rings.
5. A float is attached to the fishing line in such a way that is provided for a specific float model.
6. The tackle is loaded with lead shots in such a way that the float sinks only a couple of centimeters.
7. After that, you can start attaching the leash with a hook.

Mounting the sliding tool

You can’t do without sliding equipment if the fishing depth is greater than or equal to the length of the rod blank. If you use blind mounting in such conditions, then it is unlikely that you will be able to throw such equipment at the right distance, since the length of the hanging fishing line is very significant. In such conditions, you should use the method of sliding the attachment of the float.

Installation is carried out in such a way that the float is on the fishing line between two stoppers made of rubber or silicone. In practice, anglers use a more versatile method: they knit special stop knots. Their advantage is that the knot can be untied at any time.

The load is also mounted in a completely different way, which should also slide freely along the fishing line. A little below the float, you will have to install a stabilizing pellet, which should set the float in a vertical position. The weight of the main load must correspond to the carrying capacity of the float itself. Alternatively, you can use self-loading floats.

Float model for long casting

The model of such a float has a peculiar spindle shape, and regardless of the method of manufacture. Homemade floats do not differ in uniqueness of forms and repeat the forms of factory models. This is due to obtaining good flight characteristics, which dictate the laws of aerodynamics. Differences may relate only to the methods of fastening and methods of loading.

Some models are equipped with plumage, so they have some similarities with rockets. This helps stabilize the flight of the float, especially in windy conditions.

Floats for blind equipment are made with a metal keel, which allows it to be securely attached to the fishing line and perform long-distance casts.

Fishing at medium distances may not be as demanding, so cylindrical floats are used. They represent an elongated antenna without the obligatory thickening at the end.

Such models of floats are more reminiscent of a goose feather, which is often used by anglers as the most sensitive. In fact, these float designs are nothing more than an upgrade of the goose feather.

Since fishing conditions can be different, the attachment of the float to the fishing line can be different. In conditions of long-distance casts, floats weighing from 6 to 20 grams are used. Their attachment to the fishing line is carried out by means of carabiners. The carabiner, in turn, is attached to the bracket, which moves along the line with the help of a cambric.

Each experienced angler carries with him several inserts with floats of various carrying capacity, mounted together with the load. This approach allows you to quickly adapt to the conditions of fishing, especially on an unfamiliar reservoir. Inserts are wound on a reel and signed so as not to spend a lot of time looking for the right insert, as anglers always do not have enough time.

Fishing is one of the most exciting activities invented by man. If at the dawn of civilization, with the help of fishing, a person obtained food for himself, then in modern conditions, fishing can be considered as a hobby that allows a person to relax and gain strength. Especially exciting is not the classic fishing, when you have to sit in one place for hours, but fishing with the use of gear for long-distance casts. The angler is in constant motion, which contributes to the emergence of fishing excitement and an increase in mood.

This factor allows you to relieve fatigue in a person and distract from everyday worries, which are a great psychological burden on the shoulders of a modern person. It should be noted that the number of anglers is growing from year to year at a high rate, which indicates that a person is trying to recover in this way.