If the dishwasher breaks down, the user will have to conduct a complete inspection of the equipment. To facilitate troubleshooting, manufacturers have installed a self-diagnosis system. Error codes for Electrolux dishwashers are displayed on the display. You just need to understand its meaning to determine the cause of the problem.
How to decrypt the code and fix the breakdown in the PMM is indicated in the table below.
How to decode fault codes Electrolux
Electrolux dishwashers are available with electronic and electromechanical controls. This means that some models have an LCD display. All set functions are displayed there, as well as the time until the end of the cycle. In a PMM without a display, the fault code is displayed on the indicators. The lamp lights up several times, indicating a breakdown.
It is important to know how to restart the equipment. If you have selected the wrong mode or the error is displayed for the first time, a reboot will reset all settings:
- unplug the machine;
- wait 20 minutes;
- connect to the network.
If the code is displayed again, then you will not be able to wash the dishes until you fix the breakdown. How to do this, read below.
| Malfunction code | The number of flashes of the light bulb with a break of 5 seconds | Which means | Causes of appearance | Repair by own hands |
| i10 | 1 | Water is not poured into the PMM tank. | If water is not withdrawn within the allotted time, there may be problems c: blockage in the filling system: hose, filter, valve; water in the water supply – it may have been turned off for a while. | 1. Check and clear blockage in inlet hose. Adjust its position. Clean the mesh filter behind the hose. Check inlet valve. 2. Wait until water appears. |
| i20 | 2 | No waste water drain. | Why is this happening: 1. Clogged drain filter, pump, hose. 2. Pump blocked. 3. The drain hose has been crushed. 4. The pressure switch does not work. | How to fix the situation: 1. Clear the filter and hose from clogging. 2. Remove the pump cover and check if the impeller is blocked by debris. It can be leftover food or broken dishes. 3. Ensure that the drain hose is level. 4. Diagnostics and replacement of the pressure switch. |
| i30 | 3 | What does the code mean: the Aquastop system worked. Water in the pan. | As a result of a leak, water has accumulated in the tray of the Electrolux dishwasher. | Find and fix the leak: · in the PMM tank; in hoses and connections; in seals and cuffs. |
| i50 | 5 | Malfunction of the pump control triac. | Problems with the control board. As a result of a short circuit, the triac is faulty. | Diagnostics of the electronic board and replacement of the triac for the control of the circulation pump. |
| i60 | 6 | Heating problems. | What’s the matter: 1. Damage to the heater or its wiring. 2. The thermostat does not work. 3. Low water level for heating. 4. Malfunction of the circulation pump. 5. Incorrect operation of the module. | What you can do: 1. Inspect and replace wiring. Test the heater, in case of malfunction, install a new part. 2. Check and change the thermostat. 3-4. Inspect the pump. Due to its breakdown, water does not circulate well. 5. Repair of the main module of the dishwasher. |
| i70 | 7 | Faulty NTC thermistor. | For what reasons did the breakdown occur: the contacts were broken after a short circuit. | When washing dishes without heating, the thermistor must be replaced. |
| i80 | 8 | Incorrect operation of the Electrolux module. Memory EEPROM error. | The main module is defective. | How to solve the problem: call the wizard to flash the module. |
| i90 | 9 | Serious electronic board error. | Unable to select and install the program. | Complete board replacement. |
| iA0 | 10 | Rocker blocked. | The rocker that sprays the water does not rotate. Causes: 1. Incorrect placement of dishes in the hopper. 2. Rocker lock after a power outage. | 1. Check the correct position of the dishes. 2. Eliminate the causes of blocking. |
| ib0 | 11 | Broken turbidity sensor. | If the sensor fails, the default heavy dirt mode can be used. | Installing a new sensor. |
| iC0 | 12 | Which means: the control panel has lost communication with the board. | The dishwasher’s electronic board is defective. | Contact the service center to replace the board. |
| id0 | 13 | The tachometer does not function. | The sensor does not regulate the engine speed of the PMM “Electrolux !. | How to repair: diagnostics and change of the tachometer. |
| iF0 | 14 | Overflow of water in the tank. | The water took longer than the allotted time. | It is necessary to drain the waste fluid to resume operation. |
The simplest repair – removing the blockage – you can do it yourself. To do this, look in the instructions for the Electrolux dishwasher, where certain parts are located.
More difficult work is the replacement of nodes. You can entrust it to the master or do it yourself. In case of problems with the electronics and the Electrolux dishwasher board, it is better to contact a service center.