Contents
Landscaping is an ongoing process. You build something, you improve it. Moreover, furniture is constantly required and tables are most in demand in the country. And put in the garden, and near the house, and also in the gazebo. How to make a table for a summer residence with your own hands we will tell in this article using the example of finished projects.
Homemade table from boards from pallets
Dismantled pallets served as the material for this table. Naturally, you can use new boards. Only one condition – they must be dry. You can buy dry ones (it costs more) or buy ordinary ones, put them somewhere in ventilated piles and soak for at least 4 months, or better, six months. In general, any furniture, including garden benches, is made from dry wood.
We assemble the table for the street – put it in the gazebo, therefore we will not glue the tabletop boards, but fasten them from below, with the help of planks. This is a very simple country table and very cheap.
Having dismantled the pallets, we get boards with an individual color and pattern. Having conjured a little, shifting them several dozen times in different manners, we achieve the desired result. It turns out quite a nice table.
We take the side parts of the pallet. We use them for the frame of the table. We grind them first with coarse sandpaper, then finely bring them to the required smoothness (grain 120 and 220).
We take the strips that remained unused, with their help we fasten the countertop. We place them in the place where the joints of the boards are located. We use two self-tapping screws for fastening each board with a joint, one for a solid one.
From the processed sidewalls and two boards (also sanded), we assemble the table frame. We fix its parts with self-tapping screws at the end (two for each joint). The frame can be glued or also “planted” on self-tapping screws. Only their length is large. Under each, we pre-drill holes with a drill, the diameter of which is slightly smaller than the diameter of the self-tapping screws.
We turn the assembled countertop over and grind it. The order is the same – first with sandpaper with a large grain, then with a fine one.
Next up is installing the legs. We select four boards of the same size, check their length, adjust if necessary. Then again grinding. It’s easier than sanding already screwed legs. We fasten the sanded boards to the frame. These will be the legs. For each – two self-tapping screws fixed in a diagonal (look at the photo). For greater stability, we install jumpers at the bottom. About 10 cm can be left from the floor to the jumpers. We connect everything with self-tapping screws so that the boards do not crack, we pre-drill holes.
Next, we cover the table for giving varnish. After the first layer, the entire pile will rise. Don’t be scared, it’s normal. We take sandpaper with a fine grain and grind to smoothness.
After removing the dust, varnish again. In theory, the varnish should lie flat, but depends on the wood, so another sanding / painting cycle may be necessary. As a result, we get such a homemade country table.
If you do not like motley boards and traces of old nails, you can make their boards the same design. This table can be rectangular, maybe square. All dimensions are arbitrary – see the available space.
Country table from the remnants of the boards
This do-it-yourself table for giving is assembled from the remains of boards of different breeds and sizes. Pine boards 25 mm thick and 50 mm wide went to the frame of the tabletop, the remains of 15 * 50 mm were left on the legs. We make the frame according to the dimensions you need. This table will stand on the veranda, and it has a small width. So let’s make it not wide – 60 cm, and the length is 140 cm. The height of the legs is 80 cm (everyone in the family is tall).
We immediately cut off two long boards of 140 cm each. To make the width of the table top 60 cm, subtract twice the thickness of the board used – this is 5 cm. Short bars should be 60 cm – 5 cm = 55 cm. We fold the frame, following right angles, twist with screws. We check whether the bars are folded correctly – we measure the diagonals, they should be the same.
We cut off the boards four boards of 80 cm each, fasten them from the inside to the assembled frame. You can use 4 screws for each leg.
Approximately at the middle of the height of the legs we fasten the crossbars. This is a shelf frame. The shelf can be used for its intended purpose, and it also increases the rigidity of the structure. We fasten strictly at right angles, checking with a large square.
We put the frame on the floor, check whether it staggers or not. If everything is done correctly, it should stand rigidly. Next, take sandpaper or a grinder and grind.
Let’s start assembling the countertop. From the finishing work there were boards of different types of wood, some of which were stained. We alternate boards of different colors.
We fasten the tabletop boards with finishing nails, carefully finishing them with a finisher. On the shelf can be fixed with ordinary nails or self-tapping screws. Then smooth with a grinder. The last step is painting. Very unlucky with the choice of varnish. Bought too dark, did not like the look. Will have to sand again and paint a different color.
Wooden table with glued top
This design features L-shaped legs. They are assembled from boards of the same thickness. In this case, 20 mm. To keep them well, 5 self-tapping screws are needed. Pre-drill holes with a drill with a diameter of 1-2 mm less than the diameter of the self-tapping screws. Then, with a larger diameter drill, we drill recesses for the caps. The diameter can be matched to furniture plugs of a suitable color or made from a wooden rod. Another option is to use wood putty, to which you add wood dust that remains after sanding. After drying and sanding, traces will be difficult to find.
When assembling the legs, make sure that the angle is exactly 90°. As a pattern, you can choose a bar. First, we coat the joint of the two parts of the leg with carpentry glue, then install the screws in the following sequence: first the two extreme ones, then the middle one, and only then the other two. After the glue dries, sand the legs, varnish and dry.
It’s time to make the tabletop. It is assembled from boards of the same thickness. Pick up the size you need. You can use fragments of different widths. It is only important that everything looks organic, and the sidewalls of the boards are even and docked without gaps.
We coat the sides of the boards selected for the table top with glue, lay them on a flat surface (some kind of table) and tighten them with clamps. In this case, they managed one, but preferably at least three. We tighten so that there are no gaps in the resulting shield. We leave for a day. Having removed the clamps, we get an almost finished countertop. It still needs to be trimmed – to align the edges, and then sand it. You can trim with a jigsaw or a regular hand saw. Using a grinder is difficult to get a straight line, but you can try. After grinding, we get a beautiful countertop.
Using the same technique, you can make an oval or round countertop. It will only be necessary to draw the appropriate line and cut the glued boards along it.
To make the table look more attractive, we will make a frame. We take a thin bar, process it with sandpaper and fasten it around the perimeter of the countertop. Finishing nails can also be used. Only the planks are also pre-lubricated with carpentry glue, and then with nails.
After the glue dries, we again process the junction with sandpaper.
Now you can attach the table legs. We assemble a table frame from four boards (there is no photo, but you can do it as in the previous paragraph). We fasten it to the back of the countertop with glue, then install furniture confirmations through the countertop. Under the confirmations, a preliminary hole is drilled with an extension for the cap. Holes for fasteners are masked in the same way as on the legs.
We attach the legs to the fixed frame. We put them inside the frame. You can attach with ordinary screws. That’s it, we made a table for giving with our own hands.
How to make a wooden garden table with benches
For this table, boards of 38 * 89 mm were used (they dissolved them themselves), but you can take standard sizes. The difference in millimeters will not really affect the results. In the photo below you can see what should happen.
To connect the parts, studs 16 cm long with washers and nuts (24 pieces) were used. All other connections are made with nails 80 mm long.
The parts are installed in place, a through hole is drilled with a drill. A stud is installed in it, washers are put on both sides and nuts are tightened. Everything is tightened with a wrench. How convenient is this option? For the winter, you can disassemble and take it to a barn or garage.
Making seats
According to the drawing, we cut the boards of the required size. Everything is necessary in double quantity – for two seats. We grind the boards, pay special attention to the ends.
We cut the short segments with which we fasten the three seat boards along the edges at an angle of 45 °. First, we assemble a structure that is attached to the seat from below. We take a board about 160 cm long, at the end we attach two short boards cut at an angle to it. Attach it so that this board is in the middle.
Then we attach the legs to the resulting structure (you can use nails). Then we add more boards cut at an angle and tighten everything with studs and bolts.
We attach the seat boards to the resulting structure. Since this is a table for the street, it is not necessary to knock them down close. Leave a gap between two adjacent at least 5 mm. We nail to the supports (which are cut down), two for each board.
We fix the finished seats with four boards 160 cm long. We fasten each leg with studs (if you walk, you can put two studs by setting them diagonally or one above the other).
Putting together a table
The table is assembled in a different way. Please note that for the countertop, the transverse boards are sawn along the edges at 52 °. We fasten them at such a distance that the legs enter. Each board has 2 nails. You can finish, with small hats, or you can hammer deep, and then mask the holes with putty.
Now we need to assemble the legs-crosses. We take two boards, cross them so that the distance between their ends is 64,5 cm. We circle the intersection with a pencil. At this point, it will be necessary to remove the wood by half the thickness of the board.
We make the same notch on the second board. If you add them together, they are in the same plane. We connect with four nails.
Similarly, we make the second leg for the table. While the table is not collected.
Installing the table
Now you need to fix the legs to the structure on which the benches are installed. We put them at an equal distance from the benches, fasten them with hairpins.
Now install the table top. We also fasten it with studs. The last step is painting. Here everyone does as he likes.
Variations on a theme
According to this drawing, you can make benches and a table separately for giving, garden. The design is reliable and easy to implement.