Contents
The Blomberg washing machine is an example of German assembly quality. These are reliable machines that are on a par with the leading brands in Europe.
All modern Blomberg brand machines have a self-diagnostic system. Its main function is to search for possible problems and failures, and notify the user about this.
Fault codes are displayed on the electronic display. In older models, the indicators on the panel flash in different sequences.
If the Blomberg washing machine has served you for many years, and now it gives an error, the main thing is to figure it out. Further in the table, we will look at common SM Blomberg error codes, what their appearance means, how to troubleshoot.
Blomberg washing machine error table: what do they mean, how to fix
| Malfunction code | transcript | Causes, elimination |
| D01 | Error d01 is on the display when no water enters the machine. | This is due to a malfunction in the water intake system. Perhaps there is no water in the water supply or the pressure is too low. The inlet hose or filter may be clogged. The solenoid valve is also likely to fail. In more severe cases, the filler pipe may become blocked. |
| D02 | If d02 is displayed on the CMA display, then there is a problem with draining the water. | To understand how to fix a breakdown, you need to find its cause. This could be a blockage in the drain filter, water drain hose, or drain pipe. Damage to the drain pump (pump) is not ruled out. |
| D03 | If error d03 lights up on the CM screen, it means that the water is not heated in the machine. | The cause of this failure may be the heating element. If the heater is overgrown with scale, then the water is not heated. The heating element could burn out or short to the case. It is necessary to disassemble the case, check the heater and, if necessary, replace it. |
| D04 | If the machine shows error d04, the triac could burn out. | In the event of a short circuit, the triac needs to be replaced. |
| D05 | Blomberg shows error d05 on the display if the NTC (thermistor) is broken. | Item needs to be replaced. |
| D06 | With error d06, there is no tacho signal. | It may be necessary to check the wiring going to the tachogenerator, or replace the tachometer. |
| D07 | The washing machine issues a code d07 when there is no signal that the hatch door is locked.
| Try closing the sunroof tighter. If it does not help, you will need to replace the blocker (UBL). |
| D09 | Broken wash program selector. | The selector or wiring needs to be replaced. |
| D10 | Water overflow detected in the tank. | To remove the error, it is necessary to replace the water intake valve or repair the control unit. |
| D11 | The electronic unit does not see the water heating circuit. | With error d10, the heating element, the control board (block) or the water heating circuit may be broken. |
| D13 | No spinning. | What to do: Try to take away some of the laundry. It is also possible damage to the engine or control unit. |
Other emergency error codes for Blomberg washing machines
In some models, the breakdown codes are different, we will also briefly consider them:
| In case of breakdowns | Code meaning |
| H1 | What does H1 code mean? It is usually displayed when the hatch door of the washing machine is not tightly closed. |
| H6 | Code H6 means problems with the drive. Perhaps the belt just jumped off the pulley and it will be enough to correct it. Or the pulley, the engine, or maybe the drive belt has worn out. |
| H12 | Clogged Aquastop filter. |
| ER7 | ER7 also indicates a problem with closing the hatch door. |
You can also try to reset errors by restarting the washer:
- Unplug the machine.
- Wait 10-20 minutes.
- Turn on.
If the error disappeared and did not appear again, it may have just been a “glitch”. But if the code reappears on the scoreboard, the problem has been confirmed, and you need the help of a specialist.
Often the solution to the problem can be found on your own by looking at the user manual or our helpful articles.
E OO i na displeju gdje je 60C stalno blica i ne mogu pokrenuti perilicu…..