Most modern appliances are equipped with a self-diagnosis system – the Beko dishwasher is no exception. In the event of a malfunction, an error code is displayed. There can be several such codes, and each has its own meaning. Having learned the decoding of the error, you will quickly find the cause of the failure of the PMM.
How to decode fault codes “Beko”
In the table below, we describe all the errors of Beko dishwashers, as well as how to fix them. But for starters, you should not exclude a system failure, as a result of which a code could be displayed. To reset the error, you need to reboot the equipment.
How to reset the dishwasher:
- Unplug the machine from the mains for 15-20 minutes.
- Connect and look at the display.
- Is the error gone? Everything is in order, and you can continue to work.
- If the code is displayed again, you need to find out its meaning and fix the problem.
Before starting repairs, unplug the Beko dishwasher from the mains and turn off the water supply.
| Fault codes | Which means | Causes of appearance | Repair by own hands |
| 0000 | There is no water intake. | 1. There is no water in the water supply, or the pressure is too low. 2. The inlet valve shuts off the flow. 3. PMM inlet hose clogged or damaged. 4. The filter mesh, which is at the inlet of the intake valve, is clogged. | 1. Check the presence of water and pressure. Wait until normal delivery resumes. 2. Turn off the inlet valve to full capacity. 3. Inspect the inlet hose. It must not be bent or damaged. 4. Remove and clean the filter mesh. |
| 000 | The water in the tank does not heat up. | Breakdown reasons: 1. The heating element burned out, or its contacts were damaged. 2. Faulty thermistor that measures the water temperature in the machine. | What you can do: 1. Diagnose the heater and its wiring. Ring the contacts of the heating element with a multimeter. If broken, replace the part. 2. Check the thermistor. Install a new element. |
| N1 | Dishwasher Code Meaning: The thermostat is not working. | What happened: 1. The thermostat contacts burned out during a short circuit. 2. The temperature sensor itself has broken. | Diagnosis and replacement of a faulty sensor. |
| N2 | The heating element has failed. | 1. The heating element does not work. 2. The electronic board burned out. | Do-it-yourself repair: 1. Inspection and replacement of the heater with a serviceable part. 2. Diagnostics of the control board. If the triac that controls the heating element is damaged, the board needs to be repaired. |
| N3 | The heating element works non-stop. | The reasons for this problem in the Beko dishwasher: 1. Incorrect operation of the thermistor, which sends incorrect signals to the control module. 2. The main module is defective. | How to fix the situation: 1. Check the thermistor and replace. 2. Repair or replace with a new electronic module. |
| N4 | What does the error mean: problems with the triac of the inlet valve. | Problems with the electronic board. | Repair of the board triac or complete replacement of the element. |
| N5 | No water drain after wash cycle. | 1. Clogged drain system: filter, pump, hose. 2. The pump is blocked by a foreign object. 3. Malfunctions in the operation of the circulation pump. | How to fix the problem: 1. Check and clean the drain filter, pump, drain hose from clogging. 2. Wearing gloves, you need to inspect the impeller of the pump, which could be blocked by glass fragments. 3. Diagnostics of the circulation pump. |
| N6 | The control triac of the PMM engine does not work. | There is a problem with the control module. | Repair of the triac or replacement of the control module. |
| N7 | The pressure switch gives incorrect readings. | 1. Hopper door not closed properly. 2. The wiring of the pressure switch is broken. 3. The filling valve does not work. 4. The pressure switch is faulty. | 1. It is necessary to press the door more tightly against the dishwasher body. 2. Check the contacts of the pressure switch. 3. Diagnose valve failure. Install new part. 4. Replace pressure switch. |
The self-diagnosis system PMM “Beko” allows you to quickly detect a problem and extend the life of the equipment.
To avoid blockages, clean dishes from food before loading, arrange the plates in the trays correctly. To save the electronic part of the machine, install RCDs – they will protect the equipment from power surges in the network.