Dishwasher “AEG” does not start, the display shows a fault code. What does it mean? So the self-diagnosis system of the machine informs the user about the appearance of a breakdown. Having deciphered the code, you will understand where to look for the cause of the malfunction.
If the damage is not serious, you can fix it yourself or call a specialist.
If you started the dishwasher and saw the error code for the first time, try resetting it. Perhaps there was a network failure, so the system generated an error.
How to restart the dishwasher “AEG”? Unplug it for a few minutes, then plug it back in. Is the error gone? You can load and wash dishes. If the code is displayed again, search for a breakdown.
1. Problems with the water level sensor.
2. Clogged or pinched inlet hose.
3. The inlet tap is closed, there is no water in the water supply.
4. The inlet valve is broken.
1. Held details. If it fails, it will be replaced.
2. Inspection of the inlet hose, cleaning from blockage.
3. Checking the water in the plumbing.
4. Diagnostics of the filling valve. Replacement if necessary.
I 20 2 No water drain.
1. Clogged drain system.
2. Drain hose kinked.
3. Problems with the water level sensor.
4. Breakdown of the PMM drain pump.
How to fix the situation:
1. Check the drain hose for clogging and kinking.
2. The level sensor is inspected, a new part is installed if there is a problem.
3. The drain pump is inspected and cleaned of debris. If the pump is defective, it must be replaced.
I 30 3 Aquastop protection has tripped.
Water was found in the dishwasher tray, there was a leak.
Or the float sensor is defective.
1. An inspection of the PMM body and connections is carried out at the time of leakage.
2. Diagnostics of the Aquastop system.
I 50 5 Problems with the control module. The triac of the module that controls the pump is defective. Need diagnostics and repair of the main module. I 60 6 What does the code mean: the water does not heat up or overheats.
1. The heating element has burnt out.
2. Breakage of the level sensor.
3. Pump failure.
4. There is a problem with the thermistor.
4. The dishwasher control module is defective.
What can be done if this code appears:
1. Check and replace the heater.
2. Inspect the level sensor, its connections. Install a new part if broken.
3. If there is a problem with the installation of the machine or the pump, the water is constantly drained, so there is no heating.
You need to check the connection system, as well as the performance of the pump.
I 70 7 Wiring problems, NTC shorted. Check and replace wiring. Inspection of the NTC sensor. I 80 and I 90 8-9 Problems with eeprom communication or module firmware. Malfunction of the electronic module. Diagnostics and repair or replacement of the module. I A0 10 Sprinkler not working. You need to check and unlock the sprinkler. I b 0 11 There is a problem with the turbidity sensor.
1. Turbidity sensor not working.
2. The dishwasher needs to be cleaned.
1. Check and replace the turbidity sensor.
2. PMM cleaning.
I C0 12 No communication with user interface. Main module failure. System failure.
The dishwasher needs a reboot.
If the error has not disappeared, the module is diagnosed and repaired.
I Ad0 13 No tacho signal.
1. No water heating.
2. Uncontrolled engine speed.
The tachogenerator needs to be checked and replaced. I F0 14 No water intake. Weak water pressure. You need to wait until the normal water supply resumes.
Now you know the errors of AEG dishwashers and can read their codes. Eliminate blockage in the car under the force of each user. As for the replacement and repair of parts, it is better to entrust this work to the master.